II. Task E. Aircraft Flight Controls and Operation of Systems

⚠️ Disclaimer: This is for educational purposes only. I am not a certified flight instructor (CFI)... yet. (Working hard on it!) Until then, please don't use this as a substitute for professional flight training. Always consult a real CFI and follow your aircraft's POH. I accept no liability for any actions taken based on this content.

Part 1 - flight controls, landing gears, brakes, oil

Part 2 - fuel, powerplant, environmental, propeller, electrical

Part 3 - instruments, avionics

One lesson plan covering three decks: Part 1 (flight controls, brakes, landing gear, oil), Part 2 (fuel, powerplant, environmental, propeller, electrical) and Part 3 (instruments, avionics).

1. Lesson Objective

  • The student understands how each PA-28-161 system works, how the systems connect, and how each one can fail.
  • The student can explain the pilot’s controls and indications for each system, using the POH and the airplane itself.

2. Content

  • Part 1: primary and secondary flight controls (stabilator, antiservo tab, flaps, trim) compared with the Cessna 172; adverse yaw; toe brakes and the hydraulic disc brake system; fixed tricycle gear, oleo struts, strut exposure, tire pressure, nosewheel steering; oil system functions and limits
  • Part 2: Lycoming O-320-D3G; fuel system (low-wing fuel-pump system, usable fuel, vents, 100LL); float-type carburetor (mixture, venturi, throttle); four-stroke cycle; dual magnetos, P-lead and hot mag; crankshaft as the hub; fixed-pitch and constant-speed propellers; primer vs fuel injection; carburetor icing and carb heat; cabin heat, defroster and carbon monoxide; starter, alternator, battery, ammeter, circuit breakers; alternator failure case study
  • Part 3: pitot-static system and blockages; altimeter (setting, pressure and temperature errors), VSI and airspeed indicator with PA-28-161 markings; alternate static source; vacuum system and gyroscopic principles; attitude, heading and turn instruments; magnetic compass errors (variation, deviation, UNOS, ANDS); the PA-28-161’s avionics (G5 PFD/HSI, ADC, AHRS, GNC 355, GMA 342, transponder, ADS-B, WAAS check) and antenna locations

3. Schedule (about 2 hours 30 min; can be split into three sessions)

Segment Time
Part 1: flight controls, brakes, landing gear, oil 30 min
Part 2: fuel, carburetor, ignition, crankshaft, propeller 35 min
Part 2: primer and fuel injection, carb icing, environmental, starter, electrical 25 min
Part 3: pitot-static instruments and errors 25 min
Part 3: gyroscopic instruments, magnetic compass 20 min
Part 3: avionics and antennas, overall review 15 min

4. Equipment

  • Laptop or projector with the three decks (engine, gyro and compass videos)
  • PA-28-161 POH and school checklist
  • PA-28-161 for a walk-around: control surfaces, struts, engine compartment, antennas, panel
  • Whiteboard and markers (engine flow diagram, pitot-static diagram)
  • Garmin G5 and GNC 355 manuals; GNC 355 trainer app on an iPad

5. Instructor’s Actions

  • Build the engine flow diagram one piece at a time (fuel → carburetor → cylinder → magneto → crankshaft → propeller), asking the student to predict the next piece.
  • Ask the two key questions: where is the electrical system in the engine flow, and what turns the crankshaft first.
  • Relate every system to its cockpit control, indication and POH page.
  • For each instrument, explain the source (pitot, static, vacuum, electric) and have the student work out blockage and failure effects instead of memorizing them.
  • Show the PA-28-161’s panel and avionics, and walk the airplane to locate parts and antennas.
  • Use the alternator failure flight to discuss failure recognition and response.

6. Student’s Actions

  • Explain each system’s purpose, main parts, cockpit controls and indications.
  • Draw the engine flow and explain how the fuel, ignition and propeller systems connect.
  • Work out instrument indications for pitot or static blockage and for use of the alternate static source.
  • Apply variation and compass turning and acceleration errors to examples.
  • Locate the system parts, controls and antennas on the airplane.

7. Completion Standards

  • The student explains the operation, normal indications and common failure modes of every PA-28-161 system covered, using the POH correctly.
  • The student correctly predicts instrument indications for each pitot-static blockage and gyro failure.
  • The student explains the pilot actions for carburetor icing, a hot mag, carbon monoxide and an alternator failure.

8. References

  • PA-28-161 Pilot’s Operating Handbook: Section 2 Limitations; Section 4 Normal Procedures (4.31 Stopping Engine); Section 7 Description and Operation of the Airplane and Its Systems (7-18 alternate static source); Section 8 Handling, Servicing and Maintenance
  • Pilot’s Handbook of Aeronautical Knowledge (FAA-H-8083-25), Ch. 6 Flight Controls; Ch. 7 Aircraft Systems; Ch. 8 Flight Instruments
  • Instrument Flying Handbook (FAA-H-8083-15), Ch. 5 Flight Instruments
  • AIM Ch. 4, Section 1 (transponder and ADS-B Out operation); 14 CFR 91.215 (ATC transponder), 91.225 (ADS-B Out)
  • Garmin G5 Pilot’s Guide; Garmin GPS 175/GNC 355/GNX 375 Pilot’s Guide
Yaboong's Picture

Yaboong

Software engineer for seven years, now a pilot. CPL/IR, working toward CFI and the airline. Writing down what I learn along the way.
More about me →

Massachusetts, US gmail YouTube