II. Task B. Visual Scanning and Collision Avoidance

⚠️ Disclaimer: This is for educational purposes only. I am not a certified flight instructor (CFI)... yet. (Working hard on it!) Until then, please don't use this as a substitute for professional flight training. Always consult a real CFI and follow your aircraft's POH. I accept no liability for any actions taken based on this content.

1. Lesson Objective

  • The student understands why see-and-avoid fails and how to scan effectively to detect other aircraft.
  • The student knows the right-of-way rules and the practices that reduce collision risk in the air and around the airport.

2. Content

  • See-and-avoid responsibility (14 CFR 91.113(b)) and traffic advisories (workload permitting)
  • Why see-and-avoid fails: environmental conditions, empty-field myopia, accommodation delay, blossom effect, human factors and tunnel vision
  • High-risk areas: busy traffic patterns, practice areas, near airports and navaids
  • Blind spots of high-wing and low-wing airplanes
  • Scanning by phase of flight, the 10-degree / 1-second scan, block scan, binocular vision and windshield posts
  • Maneuvering flight and clearing turns
  • Right-of-way rules: 91.113 general rules, aircraft in distress, converging, approaching head-on, overtaking, landing (AC 90-66C in the traffic pattern)
  • Collision avoidance summary: flight deck management, lights, transponder and ADS-B, ATC services, radio calls

3. Schedule (about 45 min)

Segment Time
Introduction (NTSB safety alert, see-and-avoid duty) 5 min
Why see-and-avoid fails (vision limits, blossom video) 10 min
How to scan (phases of flight, scan methods, blind spots, clearing turns) 15 min
Right-of-way rules 10 min
Collision avoidance summary and review 5 min

4. Equipment

  • Laptop or projector with the slide deck (blossom effect video)
  • Whiteboard and markers (right-of-way diagrams)
  • Model airplanes for converging, head-on and overtaking scenarios
  • Sectional chart and Chart Supplement for local high-traffic areas

5. Instructor’s Actions

  • State the regulatory see-and-avoid duty and the limits of traffic advisories.
  • Explain each vision limitation with the photos and the blossom effect video.
  • Show high-wing and low-wing blind spots and the scanning technique for each phase of flight.
  • Demonstrate the block scan and explain clearing turns before maneuvers.
  • Use model airplanes to quiz the student on each right-of-way rule.
  • Summarize practical ways to reduce collision risk.

6. Student’s Actions

  • Explain empty-field myopia, accommodation delay and the blossom effect in his or her own words.
  • Describe a proper scan pattern and when to make clearing turns.
  • Decide who has the right-of-way in each model-airplane scenario.
  • List the equipment and procedures used to reduce collision risk.

7. Completion Standards

  • The student explains at least four reasons see-and-avoid fails and how to counter each.
  • The student describes an effective scan (short, regularly spaced eye movements of no more than 10 degrees, about 1 second each) and the scan for each phase of flight.
  • The student correctly applies the 14 CFR 91.113 right-of-way rules to all lesson scenarios.

8. References

  • 14 CFR 91.111 (operating near other aircraft), 91.113 (right-of-way rules: except water operations)
  • AC 90-48 (Pilots’ Role in Collision Avoidance)
  • AC 90-66 (Non-Towered Airport Flight Operations)
  • AIM Ch. 8, Section 1, Vision in Flight (8-1-6) and Judgment Aspects of Collision Avoidance (8-1-8)
  • Airplane Flying Handbook (FAA-H-8083-3), Ch. 1 (Collision Avoidance) and clearing procedures
  • NTSB Safety Alert SA-058 (See and Avoid)
Yaboong's Picture

Yaboong

Software engineer for seven years, now a pilot. CPL/IR, working toward CFI and the airline. Writing down what I learn along the way.
More about me →

Massachusetts, US gmail YouTube